TRANSCEIVER PARALLEL INTERFACE Fiber Optics - Transceivers 9

Reset All

Part	Manufacturer	Fiber Optic Type	Mounting Feature	Maximum Supply Voltage	Maximum Operating Temperature	Minimum Operating Temperature	Rx Data Rate	Tx Data Rate	Emitter or Detector Type	Fiber Type	Nominal Optical Power Output	Nominal Supply Voltage	Body Length/Diameter	Body Width	Sub-Category	Body Height	Nominal Operating Wavelength	Minimum Supply Voltage	Minimum Operating Wavelength	Communication Standard	Maximum Operating Wavelength	Minimum Return Loss	Additional Features	Built-in Features	Sensitivity Level
HFBR-7924EH	Broadcom	TRANSCEIVER PARALLEL INTERFACE	PANEL MOUNT	3.465 V	80 Cel	0 Cel	2700 Mbps	2700 Mbps	LASER DIODE, PIN PHOTODIODE	50/125, MMF	.354 mW	3.3 V	34.12 mm	17.5 inch	Fiber Optic Transceivers	13.12 mm	850 nm	3.135 V	830 nm	OC-192, SONET	860 nm	12 dB	10 X 10 ARRAY	AMPLIFIER	-11.7 dBm
HFBR-7924	Broadcom	TRANSCEIVER PARALLEL INTERFACE	PANEL MOUNT	3.465 V	80 Cel	0 Cel	2700 Mbps	2700 Mbps	LASER DIODE, PIN PHOTODIODE	50/125, MMF	.354 mW	3.3 V	34.12 mm	17.5 inch	Fiber Optic Transceivers	16 mm	850 nm	3.135 V	830 nm	OC-192, SONET	860 nm	12 dB	10 X 10 ARRAY	AMPLIFIER	-11.7 dBm
HFBR-7924HZ	Broadcom	TRANSCEIVER PARALLEL INTERFACE	PANEL MOUNT	3.465 V			2700 Mbps	2700 Mbps	LASER DIODE, PIN PHOTODIODE	50/125, MMF	.354 mW	3.3 V	34.12 mm	17.5 inch		12.9 mm	850 nm	3.135 V	830 nm	OC-192, SONET	860 nm	12 dB	10 X 10 ARRAY, EMITTER/DETECTOR TYPE-PREAMPLIFIER, VCSEL ARRAY, REFERENCE STANDARD-JESD22-A114-B, TUV, UL	AMPLIFIER	-18 dBm
HFBR-7924E	Broadcom	TRANSCEIVER PARALLEL INTERFACE	PANEL MOUNT	3.465 V	80 Cel	0 Cel	2700 Mbps	2700 Mbps	LASER DIODE, PIN PHOTODIODE	50/125, MMF	.354 mW	3.3 V	34.12 mm	17.5 inch	Fiber Optic Transceivers	16 mm	850 nm	3.135 V	830 nm	OC-192, SONET	860 nm	12 dB	10 X 10 ARRAY	AMPLIFIER	-11.7 dBm
HFBR-7924Z	Broadcom	TRANSCEIVER PARALLEL INTERFACE	PANEL MOUNT	3.465 V			2700 Mbps	2700 Mbps	LASER DIODE, PIN PHOTODIODE	50/125, MMF	.354 mW	3.3 V	34.12 mm	17.5 inch		12.9 mm	850 nm	3.135 V	830 nm	OC-192, SONET	860 nm	12 dB	10 X 10 ARRAY, EMITTER/DETECTOR TYPE-PREAMPLIFIER, VCSEL ARRAY, REFERENCE STANDARD-JESD22-A114-B, TUV, UL	AMPLIFIER	-18 dBm
HFBR-7924H	Broadcom	TRANSCEIVER PARALLEL INTERFACE	PANEL MOUNT	3.465 V	80 Cel	0 Cel	2700 Mbps	2700 Mbps	LASER DIODE, PIN PHOTODIODE	50/125, MMF	.354 mW	3.3 V	34.12 mm	17.5 inch	Fiber Optic Transceivers	12.9 mm	850 nm	3.135 V	830 nm	OC-192, SONET	860 nm	12 dB	10 X 10 ARRAY	AMPLIFIER	-11.7 dBm
HFBR-7924EZ	Broadcom	TRANSCEIVER PARALLEL INTERFACE	PANEL MOUNT	3.465 V			2700 Mbps	2700 Mbps	LASER DIODE, PIN PHOTODIODE	50/125, MMF	.354 mW	3.3 V	34.12 mm	17.5 inch		12.9 mm	850 nm	3.135 V	830 nm	OC-192, SONET	860 nm	12 dB	10 X 10 ARRAY, EMITTER/DETECTOR TYPE-PREAMPLIFIER, VCSEL ARRAY, REFERENCE STANDARD-JESD22-A114-B, TUV, UL	AMPLIFIER	-18 dBm
HFBR-7924EHZ	Broadcom	TRANSCEIVER PARALLEL INTERFACE	PANEL MOUNT	3.465 V			2700 Mbps	2700 Mbps	LASER DIODE, PIN PHOTODIODE	50/125, MMF	.354 mW	3.3 V	34.12 mm	17.5 inch		12.9 mm	850 nm	3.135 V	830 nm	OC-192, SONET	860 nm	12 dB	10 X 10 ARRAY, EMITTER/DETECTOR TYPE-PREAMPLIFIER, VCSEL ARRAY, REFERENCE STANDARD-JESD22-A114-B, TUV, UL	AMPLIFIER	-18 dBm
AFBR-83PDZ	Broadcom	TRANSCEIVER PARALLEL INTERFACE		3.3 V	70 Cel	0 Cel									Fiber Optic Transceivers		850 nm

Fiber Optics - Transceivers

Fiber optic transceivers are electronic devices that are used in fiber optic communication systems to transmit and receive optical signals. They are designed to both transmit and receive data over a fiber optic network, allowing for two-way communication between devices.

Fiber optic transceivers typically consist of a transmitter, a receiver, and control circuitry. The transmitter converts electrical signals into optical signals, which are then transmitted over the fiber optic cable. The receiver converts the incoming optical signal into an electrical signal, which is then processed by the control circuitry.

Fiber optic transceivers use different technologies to transmit and receive optical signals, including:

1. Direct modulation: Direct modulation uses an LED or laser diode to directly modulate the optical signal in response to an electrical signal.

2. External modulation: External modulation uses an electro-optic modulator to modulate the optical signal in response to an electrical signal.

3. Coherent detection: Coherent detection uses a local oscillator to synchronize the optical signal with a reference signal, enabling precise phase and amplitude measurements of the optical signal.

Fiber optic transceivers come in different configurations and designs, depending on the application and the required performance. They can be integrated into a fiber optic network or mounted in a separate enclosure, depending on the application and the space available.