.003 ohm Data Line Filters 7

Reset All

Part	Manufacturer	Filter Type	Maximum DC Resistance	Rated Current	Minimum Insulation Resistance	Approvals (V)	No. of Functions	Screening Level	Output Impedance (ohm)	Packing Method	Mounting Type	Rated Voltage	No. of Terminals	Dimensions	Maximum Operating Temperature	Minimum Operating Temperature	Terminal Finish	Height	Width (mm)	Maximum Insertion Loss	Additional Features	JESD-609 Code	Length	Capacitance
7427521	Wurth Elektronik	FERRITE BEAD	.003 ohm	5 A			1		211 OHM		SURFACE MOUNT		4	L8.5XB5.6XH3.2 (mm)/L0.335XB0.22XH0.126 (inch)	85 Cel	-40 Cel		3.2 mm	5.6				8.5 mm
74279221100	Wurth Elektronik	FERRITE CHIP	.003 ohm	10.5 A			1		10 OHM	TAPE AND REEL	SURFACE MOUNT		2	L3.2XB1.6XH1.1 (mm)/L0.126XB0.063XH0.043 (inch)	125 Cel	-55 Cel		1.1 mm	1.6				3.2 mm
ELKEA103FA	Panasonic	DATA LINE FILTER	.003 ohm	5 A			1			TAPE AND REEL	SURFACE MOUNT	50 V	3	L3.2XB1.8XH2.2 (mm)/L0.126XB0.071XH0.087 (inch)	85 Cel	-20 Cel	Tin/Copper (Sn/Cu)	2.2 mm	1.8		CUT OFF FREQUENCY 0.5 MHZ	e2	3.2 mm	10000 uF
RDEN-048050	TDK	DATA LINE FILTER	.003 ohm	50 A	500 Mohm	UL; CUL; CSA; EN; SEMKO	1				CHASSIS MOUNT	48 V		L70.0XB60.0XH30.0 (mm)/L2.756XB2.362XH1.181 (inch)	85 Cel	-30 Cel		30 mm	60.0				70 mm
ELKEA333FA	Panasonic	DATA LINE FILTER	.003 ohm	5 A			1			TAPE AND REEL	SURFACE MOUNT	25 V	3	L3.2XB1.8XH2.2 (mm)/L0.126XB0.071XH0.087 (inch)	85 Cel	-20 Cel	Tin/Copper (Sn/Cu)	2.2 mm	1.8		CUT OFF FREQUENCY 0.2 MHZ	e2	3.2 mm	33000 uF
742792030	Wurth Elektronik	FERRITE CHIP	.003 ohm	10 A		IEC	1	AEC-Q200	30 OHM	TR, EMBOSSED, 7 INCH	SURFACE MOUNT		2		125 Cel	-55 Cel		.9 mm	1.2				2 mm
M15733/39-0012	Defense Logistics Agency	DATA LINE FILTER	.003 ohm	10 A			1				PANEL MOUNT	100 V			125 Cel					70 dB	PI-TYPE CIRCUIT			990000 uF

Data Line Filters

Data line filters are electronic filters that are used to filter out noise and interference from data communication lines. They are designed to provide a high level of attenuation of unwanted frequencies while allowing the desired data signal to pass through with minimal distortion.

Data line filters use a combination of passive and active components, including resistors, capacitors, inductors, and op-amps, to filter out noise and interference from data communication lines. They can be designed for a wide range of communication standards, including Ethernet, USB, HDMI, and other data communication protocols.

Data line filters can be designed as low-pass filters, which allow low-frequency signals to pass through while attenuating high-frequency signals, or as band-stop filters, which block a specific range of frequencies while allowing other frequencies to pass through. They can also be designed with multiple stages of filtering to provide increased attenuation of unwanted frequencies.

Data line filters are commonly used in a variety of electronic systems, including computers, telecommunication equipment, medical equipment, and industrial control systems. They are also used in data centers and other applications where high-speed data communication is critical.