.85 A Data Line Filters 6

Reset All

Part	Manufacturer	Filter Type	Construction	Maximum DC Resistance	Maximum Frequency	Material	Rated Current	Minimum Insulation Resistance	No. of Functions	Screening Level	Output Impedance (ohm)	Packing Method	Mounting Type	Rated Voltage	No. of Terminals	Sub-Category	Dimensions	Case Code	Maximum Operating Temperature	Attenuation At Maximum Frequency	Minimum Attenuation Frequency	Minimum Operating Temperature	Attenuation At Minimum Frequency	Terminal Finish	Inductance	Maximum Attenuation Frequency	Height	Width (mm)	Additional Features	JESD-609 Code	Minimum Frequency	Length
BMB2A0060LN2	TE Connectivity	FERRITE CHIP	Multilayer Chip	.05 ohm	100 MHz	Ferrite	.85 A		1		60 OHM	TR	SURFACE MOUNT		2	Other Passive Filters	L2XB1.2XH.9 (mm)/L.0787XB.0472XH.0354 (inch)	0805	125 Cel			-55 Cel					.9 mm	1.2			100 MHz	2 mm
BKP0603HS121-T	Taiyo Yuden	FERRITE CHIP	Multilayer Chip	.15 ohm	100 MHz	Ferrite	.85 A					Tape, Paper	SURFACE MOUNT			Other Passive Filters	L.6XB.3XH.3 (mm)/L.0236XB.0118XH.0118 (inch)	0201	85 Cel			-55 Cel		MATTE TIN OVER NICKEL			.3 mm	.3		e3	100 MHz	.6 mm
BWCU00322518801Y00	Chilisin Electronics	DATA LINE FILTER		.18 ohm			.85 A	10 Mohm	2		800 OHM	TR, 7 INCH	SURFACE MOUNT	50 V	4				105 Cel			-40 Cel					1.8 mm	2.5				3.2 mm
MDF2016BSS420CTD25	TDK	FERRITE CHIP		.3 ohm			.85 A		1	AEC-Q200	42 OHM	TR, 7 INCH	SURFACE MOUNT		2				125 Cel			-40 Cel					1 mm	1.6				2 mm
1206USB-102MLC	Coilcraft	DATA LINE FILTER		.14 ohm			.85 A		2		100 OHM	TAPE AND REEL	SURFACE MOUNT		4		L3.2XB1.6XH1.83 (mm)/L0.126XB0.063XH0.072 (inch)		85 Cel	19 dB	100 MHz	-40 Cel	4.2 dB	Gold (Au) - with Nickel (Ni) barrier	.066 uH	500 MHz	1.83 mm	1.6	GOLD OVER NICKEL OVER SILVER-PALLADIUM-GLASS FRIT TERMINATION	e4		3.2 mm
BLM15EX221SN1D	Murata Manufacturing	FERRITE CHIP		.14 ohm			.85 A		1		220 OHM	TR, PAPER, 7 INCH	SURFACE MOUNT		2		L1.0XB0.5XH0.5 (mm)/L0.039XB0.02XH0.02 (inch)		125 Cel			-55 Cel		TIN			.5 mm	0.5		e3		1 mm

Data Line Filters

Data line filters are electronic filters that are used to filter out noise and interference from data communication lines. They are designed to provide a high level of attenuation of unwanted frequencies while allowing the desired data signal to pass through with minimal distortion.

Data line filters use a combination of passive and active components, including resistors, capacitors, inductors, and op-amps, to filter out noise and interference from data communication lines. They can be designed for a wide range of communication standards, including Ethernet, USB, HDMI, and other data communication protocols.

Data line filters can be designed as low-pass filters, which allow low-frequency signals to pass through while attenuating high-frequency signals, or as band-stop filters, which block a specific range of frequencies while allowing other frequencies to pass through. They can also be designed with multiple stages of filtering to provide increased attenuation of unwanted frequencies.

Data line filters are commonly used in a variety of electronic systems, including computers, telecommunication equipment, medical equipment, and industrial control systems. They are also used in data centers and other applications where high-speed data communication is critical.