50 A Data Line Filters 6

Reset All
Part RoHS Manufacturer Filter Type Construction Maximum DC Resistance Maximum Frequency Material Rated Current Minimum Insulation Resistance Approvals (V) Power Supply (V) No. of Functions Technology Screening Level Output Impedance (ohm) High Pot Packing Method Mounting Type Rated Voltage No. of Terminals Sub-Category Dimensions Case Code Maximum Operating Temperature Attenuation At Maximum Frequency Minimum Attenuation Frequency Package Material Minimum Operating Temperature Attenuation At Minimum Frequency Terminal Finish Inductance Maximum Attenuation Frequency Manufacturer Series Height Width (mm) Diameter (mm) Maximum Insertion Loss Additional Features JESD-609 Code Minimum Frequency Operating Frequency (Hz) Series Length Capacitance

RB6122-50-0M3

Schaffner Holding Ag

DATA LINE FILTER

.0009 ohm

50 A

UL

1

THROUGH HOLE MOUNT

600 V

L61.0XB57.8XH38.0 (mm)/L2.402XB2.276XH1.496 (inch)

125 Cel

-40 Cel

250 uH

38 mm

57.8

61 mm

RDEN-048050

TDK

DATA LINE FILTER

.003 ohm

50 A

500 Mohm

UL; CUL; CSA; EN; SEMKO

1

CHASSIS MOUNT

48 V

L70.0XB60.0XH30.0 (mm)/L2.756XB2.362XH1.181 (inch)

85 Cel

-30 Cel

30 mm

60.0

70 mm

RB6132-50-0M2

Schaffner Holding Ag

DATA LINE FILTER

.0009 ohm

50 A

IEC; UL

3

PANEL MOUNT

1000 V

12

125 Cel

-40 Cel

180 uH

52 mm

66.9

67.9 mm

RB6522-50-0M3

Schaffner Holding Ag

DATA LINE FILTER

.00025 ohm

50 A

IEC; UL

2

PANEL MOUNT

1000 V

8

125 Cel

-40 Cel

900 uH

58 mm

43.4

50 mm

RB8522-50-0M8

Schaffner Holding Ag

DATA LINE FILTER

.0017 ohm

50 A

IEC; UL

2

PANEL MOUNT

1000 V

8

125 Cel

-40 Cel

750 uH

80 mm

45.24

50.5 mm

RB6532-50-0M2

Schaffner Holding Ag

DATA LINE FILTER

.0008 ohm

50 A

IEC; UL

3

PANEL MOUNT

1000 V

12

125 Cel

-40 Cel

180 uH

70 mm

58

62 mm

Data Line Filters

Data line filters are electronic filters that are used to filter out noise and interference from data communication lines. They are designed to provide a high level of attenuation of unwanted frequencies while allowing the desired data signal to pass through with minimal distortion.

Data line filters use a combination of passive and active components, including resistors, capacitors, inductors, and op-amps, to filter out noise and interference from data communication lines. They can be designed for a wide range of communication standards, including Ethernet, USB, HDMI, and other data communication protocols.

Data line filters can be designed as low-pass filters, which allow low-frequency signals to pass through while attenuating high-frequency signals, or as band-stop filters, which block a specific range of frequencies while allowing other frequencies to pass through. They can also be designed with multiple stages of filtering to provide increased attenuation of unwanted frequencies.

Data line filters are commonly used in a variety of electronic systems, including computers, telecommunication equipment, medical equipment, and industrial control systems. They are also used in data centers and other applications where high-speed data communication is critical.