.7 A EMI Mains Filters 7

Reset All

Part	Manufacturer	Filter Type	Rated Current	Minimum Insulation Resistance	Approvals (V)	High Pot	Packing Method	Mounting Type	Rated Voltage	Dimensions	Maximum Operating Temperature	Minimum Operating Temperature	Terminal Finish	Height	Width (mm)	Additional Features	JESD-609 Code	Operating Frequency (Hz)	Length
SS26V-070510	KEMET Corporation	SINGLE PHASE EMI FILTER	.7 A	100 Mohm	UL	500 V	TRAY	THROUGH HOLE MOUNT	250 V	L26.0XB20.5XH30.5 (mm)/L1.024XB0.807XH1.201 (inch)	120 Cel	-25 Cel		30.5 mm	20.5				26 mm
B82793C0105N265	TDK	SINGLE PHASE EMI FILTER	.7 A		IEC; UL	750 V	TR, BLISTER, 13 INCH	SURFACE MOUNT	42 V	L7.1XB6.0XH4.9 (mm)/L0.28XB0.236XH0.193 (inch)	125 Cel	-40 Cel	TIN	4.8 mm	6	AEC-Q200	e3	50/60Hz	7.1 mm
PLA10AN1030R7R2B	Murata Manufacturing	SINGLE PHASE EMI FILTER	.7 A	100 Mohm			BOX	THROUGH HOLE MOUNT	300 V	L18.0XB16.0XH17.5 (mm)/L0.709XB0.63XH0.689 (inch)	120 Cel	-25 Cel	Tin/Copper (Sn/Cu)	17.5 mm	16.0	INDUCTANCE 10 MILLI HENRY; STANDARD WINDING TYPE	e2		18 mm
SU9V-07010	KEMET Corporation	SINGLE PHASE EMI FILTER	.7 A	100 Mohm	UL	500 V	TRAY	THROUGH HOLE MOUNT	250 V		120 Cel	-25 Cel		17 mm	11				17 mm
SS11VL-R07190	KEMET Corporation	SINGLE PHASE EMI FILTER	.7 A	100 Mohm				THROUGH HOLE MOUNT	250 V	L22.0XB14.5XH19.5 (mm)/L0.866XB0.571XH0.768 (inch)	75 Cel	-25 Cel		19.5 mm	14.5	INDUCTANCE 19 MILLI HENRY			22 mm
SSRH7H-M07196	KEMET Corporation	SINGLE PHASE EMI FILTER	.7 A	100 Mohm	UL		TRAY	THROUGH HOLE MOUNT	250 V		120 Cel	-25 Cel		12 mm	14.5				18 mm
SSR10V-07330	KEMET Corporation	SINGLE PHASE EMI FILTER	.7 A	100 Mohm	UL	500 V	TRAY	THROUGH HOLE MOUNT	250 V		120 Cel	-25 Cel		13.5 mm	18				22 mm

EMI Mains Filters

EMI mains filters are electronic filters that are used to suppress electromagnetic interference (EMI) from mains power lines. They are designed to provide a high level of attenuation of unwanted frequencies while allowing the desired power signal to pass through with minimal distortion.

EMI mains filters use a combination of passive and active components, including capacitors, inductors, resistors, and diodes, to filter out noise and interference from power lines. They can be designed for a wide range of power ratings and frequencies, depending on the application.

EMI mains filters can be designed as low-pass filters, which allow low-frequency power signals to pass through while attenuating high-frequency EMI signals, or as band-stop filters, which block a specific range of frequencies while allowing other frequencies to pass through. They can also be designed with multiple stages of filtering to provide increased attenuation of unwanted frequencies.

EMI mains filters are commonly used in a variety of electronic systems, including power supplies, motor drives, medical equipment, and industrial control systems. They are also used in residential and commercial buildings to suppress EMI noise from power lines and prevent interference with other electronic devices.