7 A EMI Mains Filters 7

Reset All

Part	Manufacturer	Filter Type	Maximum Frequency	Rated Current	Minimum Insulation Resistance	Approvals (V)	Insertion Loss At Minimum Frequency	High Pot	Maximum Leakage Current	Packing Method	Mounting Type	Rated Voltage	No. of Terminals	Dimensions	Maximum Operating Temperature	Insertion Loss At Maximum Frequency	Minimum Operating Temperature	Terminal Finish	Manufacturer Series	Height	Width (mm)	Diameter (mm)	Additional Features	JESD-609 Code	Minimum Frequency	Operating Frequency (Hz)	Length
7448027001	Wurth Elektronik	SINGLE PHASE EMI FILTER		7 A		ENEC-10; VDE				CARTON; TRAY	THROUGH HOLE MOUNT	250 V			125 Cel		-40 Cel			22 mm	14.0					50Hz	18 mm
7448040707	Wurth Elektronik	SINGLE PHASE EMI FILTER		7 A						TRAY	THROUGH HOLE MOUNT	250 V		L28.0XB19.0XH28.0 (mm)/L1.102XB0.748XH1.102 (inch)	125 Cel		-40 Cel	TIN COPPER		28 mm	19.0			e2		50Hz	28 mm
CMS1-1-R	Eaton Corporation	SINGLE PHASE EMI FILTER		7 A		UL				TAPE AND REEL	SURFACE MOUNT		4	L9.4XB7.2XH2.6 (mm)/L0.37XB0.283XH0.102 (inch)	160 Cel		-40 Cel			2.6 mm	7.2						9.4 mm
SC-07-30JM	KEMET Corporation	SINGLE PHASE EMI FILTER		7 A	100 Mohm	UL		500 V		TRAY	THROUGH HOLE MOUNT	250 V			120 Cel		-25 Cel			33 mm	23						33 mm
2-6609037-5	TE Connectivity	SINGLE PHASE EMI FILTER	5 MHz	7 A		UL; CSA; VDE	15 dB	2250 V	.21 mA		PANEL MOUNT	120 V		L109.98XB52.6XH39.6 (mm)/L4.33XB2.071XH1.559 (inch)	40 Cel	75 dB	-10 Cel			39.6 mm					.01 MHz	50/60Hz	109.98 mm
TF2514HU-101Y7R0-01	TDK	SINGLE PHASE EMI FILTER		7 A		UL; CSA; IEC					THROUGH HOLE MOUNT	280 V		D25XH14 (mm)	120 Cel		-20 Cel		TF	14 mm		25	INDUCTANCE 0.1 MILLI HENRY
SC-07-E030JH-P	KEMET Corporation	SINGLE PHASE EMI FILTER		7 A	100 Mohm	UL		500 V		TRAY	THROUGH HOLE MOUNT	250 V			120 Cel		-25 Cel			15 mm		24

EMI Mains Filters

EMI mains filters are electronic filters that are used to suppress electromagnetic interference (EMI) from mains power lines. They are designed to provide a high level of attenuation of unwanted frequencies while allowing the desired power signal to pass through with minimal distortion.

EMI mains filters use a combination of passive and active components, including capacitors, inductors, resistors, and diodes, to filter out noise and interference from power lines. They can be designed for a wide range of power ratings and frequencies, depending on the application.

EMI mains filters can be designed as low-pass filters, which allow low-frequency power signals to pass through while attenuating high-frequency EMI signals, or as band-stop filters, which block a specific range of frequencies while allowing other frequencies to pass through. They can also be designed with multiple stages of filtering to provide increased attenuation of unwanted frequencies.

EMI mains filters are commonly used in a variety of electronic systems, including power supplies, motor drives, medical equipment, and industrial control systems. They are also used in residential and commercial buildings to suppress EMI noise from power lines and prevent interference with other electronic devices.