TDK EMI Mains Filters 59

Reset All

Part	Manufacturer	Filter Type	Rated Current	Minimum Insulation Resistance	Approvals (V)	High Pot	Maximum Leakage Current	Packing Method	Mounting Type	Rated Voltage	Dimensions	Maximum Operating Temperature	Minimum Operating Temperature	Manufacturer Series	Height	Width (mm)	Diameter (mm)	Additional Features	Operating Frequency (Hz)	Length
RSHN-2006	TDK	SINGLE PHASE EMI FILTER	6 A	100 Mohm	UL; CSA; EN	500 V	1 mA		PANEL MOUNT	250 V		85 Cel	-25 Cel		35 mm	52			60Hz	98 mm
RSHN-2006L	TDK	SINGLE PHASE EMI FILTER	6 A	100 Mohm	UL; CSA; EN	500 V	.1 mA		PANEL MOUNT	250 V		85 Cel	-25 Cel		43.4 mm	52			60Hz	98 mm
TF0804S-01	TDK	SINGLE PHASE EMI FILTER	1 A						THROUGH HOLE MOUNT	50 V	D10.0XH6.0 (mm)/D0.394XH0.236 (inch)	105 Cel	-20 Cel	TF0804S-01	6 mm		10	INDUCTANCE 3 MICRO HENRY
TF2326VU-300Y5R0-1H	TDK	SINGLE PHASE EMI FILTER	5 A		UL; CSA; IEC				THROUGH HOLE MOUNT	280 V	D23XL20 (mm)	120 Cel	-20 Cel	TF			23	INDUCTANCE 30 MICRO HENRY
TF3435VU-300Y15R0-1H	TDK	SINGLE PHASE EMI FILTER	15 A		UL; CSA; IEC				THROUGH HOLE MOUNT	280 V	D33XL22 (mm)	120 Cel	-20 Cel	TF			33	INDUCTANCE 30 MICRO HENRY
B84131-M1-G135	TDK	THREE PHASE EMI FILTER	35 A		UL; CSA; VDE	2700 V	3.5 mA		PANEL MOUNT	250 V	L149XB104XH80 (mm)			B84131	80 mm	104			50/60Hz	149 mm
B84142B0012R000	TDK	SINGLE PHASE EMI FILTER	12 A		UL; CSA; ENEC-10	2700 V	3.5 mA		PANEL MOUNT	250 V	L121.0XB113.0XH61.0 (mm)/L4.764XB4.449XH2.402 (inch)				61 mm	113.0			50/60Hz	121 mm
B84113-C-B30	TDK	SINGLE PHASE EMI FILTER	3 A		UL; CSA; VDE	2700 V	.5 mA		PANEL MOUNT	250 V	L63.5XB50.8XH38.1 (mm)			B84113C	38.1 mm	50.8		TAB CONNECTORS ON FACE ENDS, MOUNTING TABS ON FACE ENDS	50/60Hz	63.5 mm
B82722S0193A041	TDK	SINGLE PHASE EMI FILTER	19 A		IEC			TR, BLISTER, 13 INCH	SURFACE MOUNT	48 V		125 Cel	-40 Cel		12.7 mm	25.4			50/60Hz	27.94 mm
B84142-B16-R	TDK	SINGLE PHASE EMI FILTER	16 A		UL; CSA; ENEC-10	2700 V	3.5 mA		PANEL MOUNT	250 V	L121.0XB113.0XH61.0 (mm)/L4.764XB4.449XH2.402 (inch)			B84142B0016R000	61 mm				50/60Hz	121 mm
TF2514HU-101Y7R0-01	TDK	SINGLE PHASE EMI FILTER	7 A		UL; CSA; IEC				THROUGH HOLE MOUNT	280 V	D25XH14 (mm)	120 Cel	-20 Cel	TF	14 mm		25	INDUCTANCE 0.1 MILLI HENRY

EMI Mains Filters

EMI mains filters are electronic filters that are used to suppress electromagnetic interference (EMI) from mains power lines. They are designed to provide a high level of attenuation of unwanted frequencies while allowing the desired power signal to pass through with minimal distortion.

EMI mains filters use a combination of passive and active components, including capacitors, inductors, resistors, and diodes, to filter out noise and interference from power lines. They can be designed for a wide range of power ratings and frequencies, depending on the application.

EMI mains filters can be designed as low-pass filters, which allow low-frequency power signals to pass through while attenuating high-frequency EMI signals, or as band-stop filters, which block a specific range of frequencies while allowing other frequencies to pass through. They can also be designed with multiple stages of filtering to provide increased attenuation of unwanted frequencies.

EMI mains filters are commonly used in a variety of electronic systems, including power supplies, motor drives, medical equipment, and industrial control systems. They are also used in residential and commercial buildings to suppress EMI noise from power lines and prevent interference with other electronic devices.