LOW SKEW CLOCK DRIVER Clock Drivers & Buffers 2,400+

Reset All

Part	Manufacturer	Logic IC Type	Temperature Grade	Terminal Form	No. of Terminals	Package Code	Package Shape	Package Body Material	Surface Mount	Input Conditioning	No. of Functions	Technology	No. of Bits	Packing Method	Nominal Supply Voltage / Vsup (V)	Power Supplies (V)	Load Capacitance (CL)	No. of Inverted Outputs	Package Style (Meter)	Package Equivalence Code	Propagation Delay (tpd)	Maximum I (ol)	Sub-Category	Terminal Pitch	Maximum Operating Temperature	Output Characteristics	Maximum Same Edge Skew (tskwd)	Minimum Operating Temperature	Terminal Finish	No. of True Outputs	Terminal Position	Control Type	Minimum fmax	JESD-30 Code	Moisture Sensitivity Level (MSL)	Maximum Supply Voltage (Vsup)	Maximum Seated Height	Width	Qualification	Output Polarity	Minimum Supply Voltage (Vsup)	Maximum Power Supply Current (ICC)	Additional Features	JESD-609 Code	Maximum Time At Peak Reflow Temperature (s)	Peak Reflow Temperature (C)	Length	Family
CGS2535TVX	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	J BEND	28	QCCJ	SQUARE	PLASTIC/EPOXY	YES	STANDARD	4	CMOS			3.3	3.3/5	50 pF	0	CHIP CARRIER	LDCC28,.5SQ	5 ns	24 Amp	Clock Drivers	1.27 mm	85 Cel		.35 ns	-40 Cel	TIN LEAD	4	QUAD			S-PQCC-J28	1	3.6 V	4.57 mm	11.43 mm	Not Qualified		3 V	.235 mA	IOH,VOH,IOL & VOL @ VCC=4.5V	e0		220	11.43 mm	ABT
SNCDC208DBLE	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	2	CMOS			5		50 pF	0	SMALL OUTLINE, SHRINK PITCH		11.5 ns			.65 mm	85 Cel	3-STATE	1 ns	-40 Cel		4	DUAL			R-PDSO-G20		5.5 V	2 mm	5.3 mm	Not Qualified		4.5 V		WITH DUAL OUTPUT ENABLE & BOTH SHOULD BE HIGH FOR TRI-STATING; CENTER PIN VCC AND GND				7.2 mm	ACT
CDCDB400RHBT	Texas Instruments	LOW SKEW CLOCK DRIVER		NO LEAD	32	HVQCCN	SQUARE	PLASTIC/EPOXY	YES	DIFFERENTIAL	1			TR, 7 INCH	3.3			0	CHIP CARRIER, HEAT SINK/SLUG, VERY THIN PROFILE	LCC32,.2SQ,20	3 ns			.5 mm	105 Cel	3-STATE WITH SERIES RESISTOR	.05 ns	-40 Cel	NICKEL PALLADIUM GOLD	8	QUAD		250 MHz	S-PQCC-N32	1	3.6 V	1 mm	5 mm			3 V	46 mA		e4		260	5 mm	CDC
SNCDC208-7DW	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	2	CMOS			5		50 pF	0	SMALL OUTLINE		11.5 ns			1.27 mm	85 Cel	3-STATE	.7 ns	-40 Cel		4	DUAL			R-PDSO-G20		5.5 V	2.65 mm	7.5 mm	Not Qualified		4.5 V		WITH DUAL OUTPUT ENABLE & BOTH SHOULD BE HIGH FOR TRI-STATING; CENTER PIN VCC AND GND				12.8 mm	ACT
CDC341DWR	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	20	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS		TR	5	5	50 pF	0	SMALL OUTLINE	SOP20,.4	4.9 ns	48 Amp	Clock Drivers	1.27 mm	70 Cel		.6 ns	0 Cel	NICKEL PALLADIUM GOLD	8	DUAL		80 MHz	R-PDSO-G20	1	5.25 V	2.65 mm	7.52 mm	Not Qualified		4.75 V	33 mA		e4	30	260	12.825 mm	341
SNCDC2351DW	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	24	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			3.3		50 pF	0	SMALL OUTLINE					1.27 mm	70 Cel	3-STATE	.5 ns	0 Cel		10	DUAL			R-PDSO-G24		3.6 V	2.65 mm	7.5 mm	Not Qualified		3 V	15 mA	MAX PART TO PART SKEW = 1NS				15.4 mm	ABT
SN65EPT21DR	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	8	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	DIFFERENTIAL	1	ECL		TR	3.3		20 pF	0	SMALL OUTLINE		1.9 ns	24 Amp		1.27 mm	85 Cel		.25 ns	-40 Cel	NICKEL PALLADIUM GOLD	1	DUAL		300 MHz	R-PDSO-G8	1	3.6 V	1.75 mm	3.9 mm	Not Qualified		3 V			e4	30	260	4.9 mm	65EP
SNCDC303DR	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	16	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	TTL			5		50 pF	2	SMALL OUTLINE					1.27 mm	70 Cel		2 ns	0 Cel		6	DUAL		80 MHz	R-PDSO-G16		5.5 V	1.75 mm	3.9 mm	Not Qualified		4.5 V	70 mA	FMAX @ CL=30PF				9.9 mm	AS
CGS2535VX	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	J BEND	28	QCCJ	SQUARE	PLASTIC/EPOXY	YES	STANDARD	4	CMOS			3.3	3.3/5	50 pF	0	CHIP CARRIER	LDCC28,.5SQ	5 ns	24 Amp	Clock Drivers	1.27 mm	70 Cel		.35 ns	0 Cel	TIN LEAD	4	QUAD			S-PQCC-J28	1	3.6 V	4.57 mm	11.43 mm	Not Qualified		3 V	.235 mA	IOH,VOH,IOL & VOL @ VCC=4.5V	e0		220	11.43 mm	ABT
SNCDC328D	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	16	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5		50 pF	0	SMALL OUTLINE		5.4 ns			1.27 mm	85 Cel		2.6 ns	-40 Cel		6	DUAL			R-PDSO-G16		5.25 V	1.75 mm	3.9 mm	Not Qualified		4.75 V	30 mA	WITH FOUR CONTROL LINES FOR PROGRAMMING OUTPUT POLARITY				9.9 mm	ABT
CDC2351QDBG4	Texas Instruments	LOW SKEW CLOCK DRIVER	AUTOMOTIVE	GULL WING	24	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS		TR	3.3	3.3	50 pF	0	SMALL OUTLINE, SHRINK PITCH	SSOP24,.3	11 ns	12 Amp	Clock Drivers	.65 mm	125 Cel	3-STATE WITH SERIES RESISTOR	2.5 ns	-40 Cel	Nickel/Palladium/Gold (Ni/Pd/Au)	10	DUAL		100 MHz	R-PDSO-G24	1	3.6 V	2 mm	5.3 mm	Not Qualified		3 V	15 mA		e4	NOT SPECIFIED	260	8.2 mm	2351
CDC304DR	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	16	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	TTL			5	5		0	SMALL OUTLINE	SOP16,.25	9 ns	48 Amp	Clock Drivers	1.27 mm	70 Cel		1 ns	0 Cel		8	DUAL		80 MHz	R-PDSO-G16		5.5 V	1.75 mm	3.9 mm	Not Qualified		4.5 V				NOT SPECIFIED	NOT SPECIFIED	9.9 mm	304
SNCDC391DBLE	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	16	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5		50 pF	0	SMALL OUTLINE, SHRINK PITCH		5 ns			.65 mm	85 Cel	3-STATE	1 ns	-40 Cel		6	DUAL			R-PDSO-G16		5.25 V	2 mm	5.3 mm	Not Qualified		4.75 V	40 mA	WITH THREE CONTROL LINES FOR PROGRAMMING OUTPUT POLARITY				6.2 mm	ABT
CDC305-1N	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	THROUGH-HOLE	16	DIP	RECTANGULAR	PLASTIC/EPOXY	NO	STANDARD	1				5	5		4	IN-LINE	DIP16,.3	9 ns	48 Amp	Clock Drivers	2.54 mm	70 Cel		1.5 ns	0 Cel		4	DUAL		80 MHz	R-PDIP-T16		5.5 V	5.08 mm	7.62 mm	Not Qualified		4.5 V				NOT SPECIFIED	NOT SPECIFIED	19.305 mm	305
CDCP1803RGER	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	NO LEAD	24	HVQCCN	SQUARE	PLASTIC/EPOXY	YES	DIFFERENTIAL	1			TR	3.3	3.3		0	CHIP CARRIER, HEAT SINK/SLUG, VERY THIN PROFILE	LCC24,.16SQ,20	.6 ns		Clock Drivers	.5 mm	85 Cel	3-STATE	.03 ns	-40 Cel	NICKEL PALLADIUM GOLD	3	QUAD		800 MHz	S-PQCC-N24	2	3.6 V	1 mm	4 mm	Not Qualified		3 V			e4	30	260	4 mm	1803
CDC339NSR	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5	5		0	SMALL OUTLINE	SOP20,.3	9 ns	48 Amp	Clock Drivers	1.27 mm	85 Cel	3-STATE	.9 ns	-40 Cel		8	DUAL		80 MHz	R-PDSO-G20		5.25 V	2 mm	5.3 mm	Not Qualified		4.75 V				NOT SPECIFIED	NOT SPECIFIED	12.6 mm	CDC
SN65EPT23DGK	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	8	TSSOP	SQUARE	PLASTIC/EPOXY	YES	DIFFERENTIAL	2	ECL		TUBE	3.3		20 pF	0	SMALL OUTLINE, THIN PROFILE, SHRINK PITCH		1.9 ns	24 Amp		.65 mm	85 Cel		.11 ns	-40 Cel	NICKEL PALLADIUM GOLD SILVER	2	DUAL		300 MHz	S-PDSO-G8	1	3.6 V	1.1 mm	3 mm	Not Qualified		3 V			e4	30	260	3 mm	65EP
LMH2180SDX	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	NO LEAD	8	HVSON	SQUARE	UNSPECIFIED	YES	STANDARD	2				2.7			0	SMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE					.5 mm	85 Cel			-40 Cel		2	DUAL		75 MHz	S-XDSO-N8		5 V	.8 mm	3 mm	Not Qualified		2.4 V						3 mm	2180
CDC351DBR	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	24	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS		TR	3.3	3.3	50 pF	0	SMALL OUTLINE, SHRINK PITCH	SSOP24,.3	4.2 ns	32 Amp	Clock Driver	.65 mm	70 Cel	3-STATE	.8 ns	0 Cel	NICKEL PALLADIUM GOLD	10	DUAL		100 MHz	R-PDSO-G24	1	3.6 V	2 mm	5.3 mm	Not Qualified		3 V	25 mA		e4	30	260	8.2 mm	351
SNCDC351DBLE	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	24	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			3.3		50 pF	0	SMALL OUTLINE, SHRINK PITCH					.65 mm	70 Cel	3-STATE	.5 ns	0 Cel		10	DUAL			R-PDSO-G24		3.6 V	2 mm	5.3 mm	Not Qualified		3 V	25 mA	MAX PART TO PART SKEW = 1NS				8.2 mm	ABT
SNCDC328ADB	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	16	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5		50 pF	0	SMALL OUTLINE, SHRINK PITCH		5.5 ns			.65 mm	85 Cel		1.1 ns	-40 Cel		6	DUAL			R-PDSO-G16		5.25 V	2 mm	5.3 mm	Not Qualified		4.75 V	32 mA	WITH FOUR CONTROL LINES FOR PROGRAMMING OUTPUT POLARITY				6.2 mm	ABT
CDC3S04YFFR	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	BALL	20	VFBGA	RECTANGULAR	UNSPECIFIED	YES	STANDARD	1			TR	1.8	1.8	10 pF	0	GRID ARRAY, VERY THIN PROFILE, FINE PITCH	BGA20,4X5,16	3 ns	3 Amp	Clock Drivers	.4 mm	85 Cel		.05 ns	-40 Cel	Tin/Silver/Copper (Sn/Ag/Cu)	4	BOTTOM		52 MHz	R-XBGA-B20	1	1.95 V	.625 mm	1.905 mm	Not Qualified		1.65 V			e1	NOT SPECIFIED	260	2.305 mm	CDC
CGS74CT2525N	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL			DIP				STANDARD	1	CMOS			5			0			10.1 ns			2.54 mm	85 Cel		.55 ns	-40 Cel		8						5.5 V	5.08 mm	7.62 mm			4.5 V						19.18 mm	CMOS
SNCDC208-7DBLE	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	2	CMOS			5		50 pF	0	SMALL OUTLINE, SHRINK PITCH		11.5 ns			.65 mm	85 Cel	3-STATE	.7 ns	-40 Cel		4	DUAL			R-PDSO-G20		5.5 V	2 mm	5.3 mm	Not Qualified		4.5 V		WITH DUAL OUTPUT ENABLE & BOTH SHOULD BE HIGH FOR TRI-STATING; CENTER PIN VCC AND GND				7.2 mm	ACT
CDC340DWRG4	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	20	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5	5		0	SMALL OUTLINE	SOP20,.4	4.8 ns	48 Amp	Clock Drivers	1.27 mm	70 Cel		.6 ns	0 Cel		8	DUAL		40 MHz	R-PDSO-G20		5.25 V	2.65 mm	7.52 mm	Not Qualified		4.75 V				NOT SPECIFIED	NOT SPECIFIED	12.825 mm	340
CDC339DB	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS		TUBE	5	5		0	SMALL OUTLINE, SHRINK PITCH	SSOP20,.3	9 ns	48 Amp	Clock Drivers	.65 mm	85 Cel	3-STATE	.9 ns	-40 Cel	NICKEL PALLADIUM GOLD	8	DUAL		80 MHz	R-PDSO-G20	1	5.25 V	2 mm	5.3 mm	Not Qualified		4.75 V	85 mA		e4	30	260	7.2 mm	CDC
CDC208NSRG4	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	2	CMOS	4	TR	5	5	50 pF	0	SMALL OUTLINE	SOP20,.3	11.7 ns	24 Amp	Bus Driver/Transceivers	1.27 mm	85 Cel	3-STATE	1 ns	-40 Cel	Nickel/Palladium/Gold (Ni/Pd/Au)	4	DUAL	ENABLE LOW	60 MHz	R-PDSO-G20	1	5.5 V	2 mm	5.3 mm	Not Qualified	TRUE	4.5 V	.08 mA		e4	NOT SPECIFIED	260	12.6 mm	208
CDCDB803RSLT	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	NO LEAD	48	HVQCCN	SQUARE	PLASTIC/EPOXY	YES	DIFFERENTIAL	1	CMOS		TR	3.3			0	CHIP CARRIER, HEAT SINK/SLUG, VERY THIN PROFILE	LCC48,.24SQ,16	3 ns			.4 mm	105 Cel		.05 ns	-40 Cel	NICKEL PALLADIUM GOLD	16	QUAD		250 MHz	S-PQCC-N48	1	3.6 V	1 mm	6 mm			3 V	9 mA		e4		260	6 mm	CDC
SN65EPT21DGK	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	8	TSSOP	SQUARE	PLASTIC/EPOXY	YES	DIFFERENTIAL	1	ECL		TUBE	3.3		20 pF	0	SMALL OUTLINE, THIN PROFILE, SHRINK PITCH		1.9 ns	24 Amp		.65 mm	85 Cel		.25 ns	-40 Cel	NICKEL PALLADIUM GOLD	1	DUAL		300 MHz	S-PDSO-G8	1	3.6 V	1.1 mm	3 mm	Not Qualified		3 V			e4	30	260	3 mm	65EP
SNCDC2351DWR	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	24	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			3.3		50 pF	0	SMALL OUTLINE					1.27 mm	70 Cel	3-STATE	.5 ns	0 Cel		10	DUAL			R-PDSO-G24		3.6 V	2.65 mm	7.5 mm	Not Qualified		3 V	15 mA	MAX PART TO PART SKEW = 1NS				15.4 mm	ABT
SNCDC329AD	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	16	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5		50 pF	0	SMALL OUTLINE		5.9 ns			1.27 mm	85 Cel		1.5 ns	-40 Cel		6	DUAL			R-PDSO-G16		5.25 V	1.75 mm	3.9 mm	Not Qualified		4.75 V	40 mA	WITH FOUR CONTROL LINES FOR PROGRAMMING OUTPUT POLARITY				9.9 mm	ABT
CDC319DBG4	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	28	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1				3.3	3.3	30 pF	0	SMALL OUTLINE, SHRINK PITCH	SSOP28,.3	3.6 ns	6 Amp	Clock Drivers	.65 mm	70 Cel	3-STATE	.25 ns	0 Cel	NICKEL PALLADIUM GOLD	10	DUAL			R-PDSO-G28	1	3.465 V	2 mm	5.3 mm	Not Qualified		3.135 V	.5 mA		e4	30	260	10.2 mm	319
CDC341DWRG4	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	20	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS		TR	5	5	50 pF	0	SMALL OUTLINE	SOP20,.4	4.9 ns	48 Amp	Clock Drivers	1.27 mm	70 Cel		.6 ns	0 Cel	Nickel/Palladium/Gold (Ni/Pd/Au)	8	DUAL		80 MHz	R-PDSO-G20	1	5.25 V	2.65 mm	7.52 mm	Not Qualified		4.75 V	33 mA		e4	NOT SPECIFIED	260	12.825 mm	341
SN74ABT337N	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	THROUGH-HOLE	20	DIP	RECTANGULAR	PLASTIC/EPOXY	NO	STANDARD	1	BICMOS			5	5		0	IN-LINE	DIP20,.3		48 Amp	Clock Drivers	2.54 mm	70 Cel	3-STATE		0 Cel		8	DUAL		80 MHz	R-PDIP-T20		5.5 V	5.08 mm	7.62 mm	Not Qualified		4.5 V				NOT SPECIFIED	NOT SPECIFIED	24.325 mm	ABT
SNCDC208N	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	THROUGH-HOLE	20	DIP	RECTANGULAR	PLASTIC/EPOXY	NO	STANDARD	2	CMOS			5		50 pF	0	IN-LINE		11.5 ns			2.54 mm	85 Cel	3-STATE	1 ns	-40 Cel		4	DUAL			R-PDIP-T20		5.5 V	5.08 mm	7.62 mm	Not Qualified		4.5 V		WITH DUAL OUTPUT ENABLE & BOTH SHOULD BE HIGH FOR TRI-STATING; CENTER PIN VCC AND GND				24.325 mm	ACT
CDC351IDWR	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	24	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			3.3	3.3		0	SMALL OUTLINE	SOP24,.4	4.2 ns	32 Amp	Clock Drivers	1.27 mm	85 Cel	3-STATE	.9 ns	-40 Cel		10	DUAL		100 MHz	R-PDSO-G24		3.6 V	2.65 mm	7.5 mm	Not Qualified		3 V				NOT SPECIFIED	NOT SPECIFIED	15.4 mm	351
CDC208NSR	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	2	CMOS	4	TR	5	5	50 pF	0	SMALL OUTLINE	SOP20,.3	11.7 ns	24 Amp	Bus Driver/Transceivers	1.27 mm	85 Cel	3-STATE	1 ns	-40 Cel	NICKEL PALLADIUM GOLD	4	DUAL	ENABLE LOW	60 MHz	R-PDSO-G20	1	5.5 V	2 mm	5.3 mm	Not Qualified	TRUE	4.5 V	.08 mA		e4	30	260	12.6 mm	208
SNCDC208-7DB	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	2	CMOS			5		50 pF	0	SMALL OUTLINE, SHRINK PITCH		11.5 ns			.65 mm	85 Cel	3-STATE	.7 ns	-40 Cel		4	DUAL			R-PDSO-G20		5.5 V	2 mm	5.3 mm	Not Qualified		4.5 V		WITH DUAL OUTPUT ENABLE & BOTH SHOULD BE HIGH FOR TRI-STATING; CENTER PIN VCC AND GND				7.2 mm	ACT
CDC339NSRG4	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5	5		0	SMALL OUTLINE	SOP20,.3	9 ns	48 Amp	Clock Drivers	1.27 mm	85 Cel	3-STATE	.9 ns	-40 Cel		8	DUAL		80 MHz	R-PDSO-G20		5.25 V	2 mm	5.3 mm	Not Qualified		4.75 V						12.6 mm	CDC
DS3245J	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL EXTENDED	THROUGH-HOLE	16	DIP	RECTANGULAR	CERAMIC, GLASS-SEALED	NO	STANDARD	1				5			0	IN-LINE					2.54 mm	75 Cel			0 Cel		4	DUAL			R-GDIP-T16		5.25 V	5.08 mm	7.62 mm			4.75 V		LG_MAX				19.94 mm	3245
SNCDC341DW	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	20	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5		50 pF	0	SMALL OUTLINE		4.9 ns			1.27 mm	70 Cel		.6 ns	0 Cel		8	DUAL			R-PDSO-G20		5.25 V	2.65 mm	7.5 mm	Not Qualified		4.75 V	33 mA	STROBED OUTPUT; MAX PART TO PART SKEW = 1NS				12.8 mm	ABT
DS3245N	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL EXTENDED	THROUGH-HOLE	16	DIP	RECTANGULAR	PLASTIC/EPOXY	NO	STANDARD	1				5			0	IN-LINE					2.54 mm	75 Cel			0 Cel		4	DUAL			R-PDIP-T16		5.25 V	5.08 mm	7.62 mm			4.75 V						21.755 mm	3245
SN65ELT22D	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	8	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	2			TUBE	5			0	SMALL OUTLINE		1.1 ns			1.27 mm	85 Cel		.1 ns	-40 Cel	NICKEL PALLADIUM GOLD	2	DUAL			R-PDSO-G8	1	5.7 V	1.75 mm	3.9 mm	Not Qualified		4.2 V			e4	30	260	4.9 mm	65ELT
SN54CDC341WR	Texas Instruments	LOW SKEW CLOCK DRIVER	MILITARY	FLAT	20	DFP	RECTANGULAR	CERAMIC, GLASS-SEALED	YES	STANDARD	1	BICMOS			5			0	FLATPACK		7 ns			1.27 mm	125 Cel		1.9 ns	-55 Cel		8	DUAL		33 MHz	R-GDFP-F20		5.5 V	2.54 mm	6.92 mm	Not Qualified		4.5 V						13.09 mm	CDC
SN65EPT23DR	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	8	SOP	RECTANGULAR	PLASTIC/EPOXY	YES	DIFFERENTIAL	2	ECL		TR	3.3		20 pF	0	SMALL OUTLINE		1.9 ns	24 Amp		1.27 mm	85 Cel		.11 ns	-40 Cel	NICKEL PALLADIUM GOLD	2	DUAL		300 MHz	R-PDSO-G8	1	3.6 V	1.75 mm	3.9 mm	Not Qualified		3 V			e4	30	260	4.9 mm	65EP
CDC208DBLE	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	20	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	2	CMOS	4	TR	5	5	50 pF	0	SMALL OUTLINE, SHRINK PITCH	SSOP20,.3	11.7 ns	24 Amp	Bus Driver/Transceivers	.65 mm	85 Cel	3-STATE	1 ns	-40 Cel		4	DUAL	ENABLE LOW	60 MHz	R-PDSO-G20		5.5 V	2 mm	5.3 mm	Not Qualified	TRUE	4.5 V				NOT SPECIFIED	NOT SPECIFIED	7.2 mm	208
CDC329ADBLE	Texas Instruments	LOW SKEW CLOCK DRIVER	INDUSTRIAL	GULL WING	16	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5	5		0	SMALL OUTLINE, SHRINK PITCH	SSOP16,.3	5.9 ns		Clock Drivers	.65 mm	85 Cel		1.5 ns	-40 Cel		6	DUAL			R-PDSO-G16		5.25 V	2 mm	5.3 mm	Not Qualified		4.75 V				NOT SPECIFIED	NOT SPECIFIED	6.2 mm	329
CDC340DBLE	Texas Instruments	LOW SKEW CLOCK DRIVER	COMMERCIAL	GULL WING	20	SSOP	RECTANGULAR	PLASTIC/EPOXY	YES	STANDARD	1	BICMOS			5	5		0	SMALL OUTLINE, SHRINK PITCH	SSOP20,.3	4.8 ns	48 Amp	Clock Drivers	.65 mm	70 Cel		.6 ns	0 Cel		8	DUAL			R-PDSO-G20		5.25 V	2 mm	5.3 mm	Not Qualified		4.75 V				NOT SPECIFIED	NOT SPECIFIED	7.2 mm	340

Clock Drivers & Buffers

Clock drivers and buffers are two electronic components commonly used in digital systems to control the timing and distribution of clock signals.

Clock drivers are electronic components that generate a clock signal and distribute it to multiple components or devices within a digital system. The clock signal is a periodic waveform that synchronizes the timing of different operations within the system. The clock driver typically amplifies and shapes the clock signal to ensure that it meets the timing requirements of the system.

Buffers, on the other hand, are electronic components that amplify and isolate signals. In digital systems, buffers are often used to distribute clock signals to multiple components without degrading the quality of the signal. Buffers can help to reduce signal distortion, noise, and jitter, which can be particularly important in high-speed digital systems.

Buffers can also be used to isolate signals and prevent interference between different components or devices. They can be particularly useful in situations where the output of one device or component could damage another device or component.

Clock drivers and buffers can be used together to distribute clock signals throughout a digital system while maintaining signal integrity. The clock driver generates the clock signal and distributes it to the buffers, which then amplify and isolate the signal before distributing it to the various components or devices within the system.